Control an RGB led using a remote control

In this example we will control an RGB led with a remote control, this will involve us connecting an infrared reciever to our Arduino as well.

We will use the buttons 1,2 and 3 to control the Red, Green and blue colours of the RGB LED. You will be able to switch the colours ona nd off which of course means you can mix the colours as well

Here is the remote control we will use in this example
1pcs/lot 38khz MCU learning board IR remote control Infrared decoder for protocol remote control For arduino

Layout

Arduino pins used

Pin 3 : IR receiver input
Pin 8 : Red cathode
Pin 9 : Green Cathode
Pin 10 : Blue Cathode

I used an IR module and RGB led module as well, the following shows this

 

Code

The code needs the IRremote remote library to be installed. Then you need to find the codes for the various buttons on the remote control that you wish to use

[codesyntax lang=”cpp”]
#include <IRremote.h>

int RECV_PIN = 3;

IRrecv irrecv(RECV_PIN);

decode_results results;

void setup()
{
Serial.begin(9600);
irrecv.enableIRIn(); // Start the receiver
}

void loop()
{
if (irrecv.decode(&results))
{
Serial.println(results.value, HEX);
irrecv.resume();
}
}
[/codesyntax]

Now upload the code above and open the serial monitor, when you press each button you should see the hex code for the keys you want to use, here is an example

0xFF30CF
0xFF18E7

These are the hex codes for buttons 1 and 2, we will use these in our full example underneath

Here is the complete code example

[codesyntax lang=”cpp”]

#include <IRremote.h>

int RECV_PIN = 3;
#define  redpin 8 
#define  greenpin 9
#define  bluepin 10 

boolean state1 = true;
boolean state2 = true;
boolean state3 = true;

IRrecv irrecv(RECV_PIN);
decode_results results;

void setup()  
{
    Serial.begin(9600);
    pinMode(redpin, OUTPUT);
    pinMode(greenpin, OUTPUT);
    pinMode(bluepin, OUTPUT);
    // Set high for common anode type
    digitalWrite(redpin, HIGH);  
    digitalWrite(greenpin, HIGH);
    digitalWrite(bluepin, HIGH);
  irrecv.enableIRIn(); // Start the receiver
}
 

void loop()  
{
  if (irrecv.decode(&results))
  {
    switch(results.value)
    {
      case 0xFF30CF:  
        Serial.println("1");
        if(state1==true)
        {
          digitalWrite(redpin, LOW);  //red on 
          state1=false; //change the state
        }  
        else
        {
          digitalWrite(redpin, HIGH);  //red off
          state1=true; //change the state
        }      
        break;
        
      case 0xFF18E7:  
        Serial.println("2"); 
        if(state2==true)
        {
          digitalWrite(greenpin, LOW); //green on 
          state2=false;
        }
        else
        {
          digitalWrite(greenpin, HIGH); //green off 
          state2=true; //change the state          
        }
        break;
        
      case 0xFF7A85:  
        Serial.println("3"); 
        if(state3==true)
        {
          digitalWrite(bluepin, LOW);  //blue on
          state3=false;
        }
        else
        {
          digitalWrite(bluepin, HIGH);  //blue off
          state3=true;           
        }
        break;
        
        
      case 0xFF6897:  
        Serial.println("OFF"); 
        digitalWrite(redpin, HIGH);
        digitalWrite(greenpin, HIGH);
        digitalWrite(bluepin, HIGH); 
        state1 = true;
        state2 = true;
        state3 = true;
        break;
        
      default :
          Serial.println("Invalid Option");
        break;
    }
  delay(250);
  irrecv.resume();
  }
}

[/codesyntax]

 

Links

KEYES Infrared receiver sensor module for arduino
5PCS/LOT RGB 3 Color SMD Full Color LED Module For Arduino