MSP430FR4133 LaunchPad and BH1745NUC Sensor example using Energia

In this article we look at a BH1745NUC Luminance and Colour Sensor and connect it to a MSP430FR4133 LaunchPad

As usual we take a look at some information regarding the sensor

The BH1745NUC is digital color sensor IC with I²C bus interface. This IC senses Red, Green and Blue light (RGB) and converts them to digital values. The high sensitivity, wide dynamic range and excellent Ircut characteristics makes this IC the most suitable to obtain the illuminance and color temperature of ambient light for adjusting LCD backlight of TV, mobile phone and tablet PC. It is possible to detect very wide range light intensity. (0.005 – 40k lx)

Specifications:

VCC Voltage Range: 2.3V to 3.6V
Maximum Sensitivity: 0.005Lx/step
Current Consumption: 130μA (Typ)
Standby Mode Current: 0.8μA (Typ)
Operating Temperature Range: -40°C to +85°C

Features

The High Sensitivity and Wide Dynamic Range (0.005 – 40k lx)
Supports Low Transmittance (Dark) Window
Correspond to I²C Bus Interface
Low Current by Power Down Function
Rejecting 50Hz/60Hz Light Noise
Correspond to 1.8V Logic Interface
Programmable Interrupt Function
It is possible to select 2 type of I²C bus slave address (ADDR =’L’: “0111000”, ADDR =’H’: “0111001”)

Here is a module that I purchased

 

 

Parts Required

I connected a sensor shield to an Arduino and then the sensor via connecting wire

Name	Link
MSP430FR4133 LaunchPad	MSP430FR4133 LaunchPad development board MSP-EXP430FR4133
BH1745NUC	BH1745NUC Digital Color Sensor RGB Detecting Sensor Light Module
Connecting wire	Free shipping Dupont line 120pcs 20cm male to male + male to female and female to female jumper wire

 

Schematic/Connection

Here are the connectors on the launchpad

 

MSP430FR4133 Launchpad	Sensor
3.3v	VIN
Gnd	Gnd
SDA P8_2	SDA
SCL P8_3	SCL

Code Example

I tried a couple of libraries but could not get them to work

This is a controleverything example which only uses built in libraries – they have code examples for various platforms. This is an Arduino one

[codesyntax lang=”cpp”]

#include <Wire.h>

// I2C address of the BH1745NUC
#define Addr 0x38

void setup()
{
    // Initialise I2C communication as MASTER
    Wire.begin();
    // Initialise serial communication, set baud rate = 9600
    Serial.begin(9600);

    // Start I2C Transmission
    Wire.beginTransmission(Addr);
    // Select mode control register1
    Wire.write(0x41);
    // Set RGBC measurement time 160 msec
    Wire.write(0x00);
    // Stop I2C Transmission
    Wire.endTransmission();
    
    // Start I2C Transmission
    Wire.beginTransmission(Addr);
    // Select mode control register2
    Wire.write(0x42);
    // Set measurement mode is active, gain = 1x
    Wire.write(0x90);
    // Stop I2C Transmission
    Wire.endTransmission();
    
    // Start I2C Transmission
    Wire.beginTransmission(Addr);
    // Select mode control register3
    Wire.write(0x44);
    // Set default value
    Wire.write(0x02);
    // Stop I2C Transmission
    Wire.endTransmission();
    delay(300);
}

void loop()
{
    unsigned int data[8];
    for(int i = 0; i < 8; i++)
    {
        // Start I2C Transmission
        Wire.beginTransmission(Addr);
        // Select data register
        Wire.write((80+i));
        // Stop I2C Transmission
        Wire.endTransmission();
        
        // Request 1 byte of data from the device
        Wire.requestFrom(Addr, 1);
        
        // Read 8 bytes of data
        // Red lsb, Red msb, Green lsb, Green msb, Blue lsb, Blue msb
        // cData lsb, cData msb
        if(Wire.available() == 1)
        {
            data[i] = Wire.read();
        }
        delay(300);
    }

    // Convert the data
    int red = ((data[1] & 0xFF) * 256) + (data[0] & 0xFF);
    int green = ((data[3] & 0xFF) * 256) + (data[2] & 0xFF);
    int blue = ((data[5] & 0xFF) * 256) + (data[4] & 0xFF);
    int cData = ((data[7] & 0xFF) * 256) + (data[6] & 0xFF);
    
    // Output data to serial monitor
    Serial.print("Red Color luminance  : ");
    Serial.println(red);
    Serial.print("Green Color luminance : ");
    Serial.println(green);
    Serial.print("Blue Color luminance : ");
    Serial.println(blue);
    Serial.print("Clear Data Color luminance : ");
    Serial.println(cData);
}

[/codesyntax]

 

Output

Open the serial monitor and you should see something like the following

Red Color luminance : 29
Green Color luminance : 27
Blue Color luminance : 10
Clear Data Color luminance : 3
Red Color luminance : 28
Green Color luminance : 27
Blue Color luminance : 10
Clear Data Color luminance : 3
Red Color luminance : 28
Green Color luminance : 26
Blue Color luminance : 10
Clear Data Color luminance : 3

Place different colored objects beside the sensor and check the values